Showing results: 211 - 225 of 405 items found.
-
SAM-3 -
Macintyre Electronic Design Associa
The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.
-
BAT-200 -
Neulog
The Battery module supplies power to a sensor, or chain ofsensors, operating in the Off-Line mode, and to sensors connectedto an RF communication module.The Battery module can be recharged by connecting it to the PC'sUSB socket via the USB module's USB cable.
-
HyperOCR -
Sea-Bird Scientific
Hyperspectral ocean color radiometer (HOCR) sensors are designed for applications where performance, size and power are key constraints. HOCRs can be mounted on real-time profilers, moored on autonomous deepwater buoys, installed in autonomous underwater vehicles, as well as on ships and airplanes for above-water optic applications. HyperOCR sensors are fully digital optical packages, providing 136 channels of calibrated optical data from 350–800 nm.
-
Keysight Technologies
The EPM and EPM-P Series provides high-performance, programmable power meters for CW, average and peak power measurements. EPM Series: measure average power over a range -70 dBm to +44 dBm, and over frequency range 9 kHz to 110 GHzEPM-P Series: measure peak, average and time-gated power over -65 dBm to +20 dBm, to 18 GHz using E932XA power sensors. It provides complete pulse and statistical analysis with PC software via the GPIB or RS232
-
mks Ophir
Ophir has a number of ways to measure high laser powers up to 12kW without heavy water cooled equipment. Most of today’s lasers can be set to emit for a short, precisely controlled period of time. If a short exposure to the laser of 0.3 – 10s is sufficient to measure the power then there are compact, uncooled sensors available for this purpose.
-
ZET 412 -
ZETLAB Company
The Signal amplifier ZET 412 with pseudo-galvanic separation is intended for amplification of input signals from various primary transducers and their transmission to the measuring unit (e.g., ZET 210 ADC/DAC unit) as well as for power supply of the connected sensors.
-
N Series -
IDS Imaging Development Systems GmbH
The compact and robust aluminum housing of the camera with lockable GPIO connector for trigger and flash and GigE connector, has two monochrome CMOS sensors and a projector. The projector is available either with blue lights in the visible area or with infrared lights. Via Power over Ethernet a data transfer and power supply are possible with long cable lengths.
-
AT-2040 -
Agate Technology
With AT-2040 you will find the features required for your application without having to install cumbersome and expensive addons. AT-2040 features a full-automatic sensitivity test mode, sensor simulation, power supply output for sensors that require voltage such as the 7310 and 991V aviation sensors, a built-in sensor charge amplifier for both single-ended and differential charge accelerometers, and a custom sensor input that can be configured to fit most accelerometers with a one to one cable.
-
BeamTrack -
mks Ophir
Thermal sensors that measure laser power and single shot energy like standard thermal sensors but in addition measure laser beam position and laser size. This position sensing detector measures laser beam position to 0.1mm accuracy and laser size measurement of a Gaussian beam to +/-5% accuracy. Measuring laser position is important for laser alignment where the laser position sensor can provide feedback to the laser position control.
-
imc Test & Measurement GmbH
For measurements on rotating components and moving machinery, imc offers modern telemetry systems for a wide variety of tasks: whether single-channel torque monitoring of a rotating shaft, multi-channel strain gauge and temperature measurements on a train wheel-set or non-contact power measurement on a vehicle drivetrain in harsh environments. There are transmission electronics available for a large variety of sensors, such as strain gauge (quarter-, half- and full-bridge), thermocouples, PT100/1000, as well as IEPE sensors and voltage signals.
-
Rohde & Schwarz GmbH & Co. KG
Our RF & microwave power sensors ensure precise and reliable measurements. They provide the highest measurement accuracy and speed, simple operation, technological leadership in thermal, diode and OTA core measurement elements as well as traceability to national standards.
-
Keysight Technologies
Make accurate and reliable measurements in the 50 to 110 GHz frequency range. Keysight's waveguide power sensors offer best SWR, high reliability and low loss, and come with a 50 MHz calibration port to reduce measurement uncertainties.
-
PCB Piezotronics, Inc.
PCB Piezotronics manufactures a wide variety of electronics to power ICP®, PE (Charge Mode), MEMS, strain gage and other types of sensors. All of these products provide conditioning of sensor signals for transmission to data acquisition systems.
-
PDU-200 -
Konrad Technologies GmbH
The PDU-200 is a power distribution unit for automatic tests equipment (ATE). Its outputs are software controlled to allow power on sequencing and direct interaction form the test sequence. The integrated 24V power supply provides power for additional equipment like relays and sensors. The PDU-200 is intended to use with an external remote-control panel which provides On & Off buttons as well as an E-Stop and acknowledge button. It’s integrated eight port switch simplifies wiring as no additional components are required.
-
Ferrites India
The tip of the unit detects the field polarity. The magnet surface is placed parallel to the unit tip. Two 1.5V AA battery operated. Power ON Switch activates the sensors and gives visual indication in form of two LEDs placed on the arm of the unit.